Samsung
DVM S - SLIM

Equipo de aire acondicionado mono-split de conductos comercial

Download BIM/CAD
AutoCAD
4
Revit
3
Solicitar un archivo BIM / CAD

Product
Samsung / DVM S - SLIM / Equipo de aire acondicionado mono-split de conductos comercial

ADD TO WISHLIST OR PROJECT
Resumen

DVM S - SLIM By Samsung

Colección
Tipo

Equipo de aire acondicionado mono-split de conductos comercial

• Fan with inverter motor; adjustable static pressure up to 40Pa
• Thickness of only 199 mm
• Condensate drainage pump 750 mmh2o (optional); filter included
• Possibility of fixed-point air supply
• Possibility of rear or lower side intake
• Communication with "Nasa" protocol
• Built-in EEV electronic expansion valve (2000 step)
• Power supply: single-phase 220 V - 50 Hz

Product codes:
AM017FNLDEH/EU
AM022FNLDEH/EU
AM028FNLDEH/EU
AM036FNLDEH/EU
AM045FNLDEH/EU
AM056FNLDEH/EU
AM071FNLDEH/EU

The variable flow system DVM (Digital variable Multi) by Samsung allows, thanks to the exclusive use of the dual inverter compressor (produced by Samsung), a high efficiency at
partial loads and a quick start-up in heating/cooling, while Flash injection technology guarantees high performance especially at low temperatures.‎
The variable flow of refrigerant technology optimizes the consumption of electricity as it is able to vary the power supplied according to the thermal demand in the rooms to be air conditioned.‎
The cycle efficiency with Inverter scroll compressor and Flash injection technology is superior to that of a traditional compressor, as the additional capacity resulting from undercooling is obtained with less power absorbed: the steam, produced in the undercooling process, is compressed only from an intermediate pressure (higher than the intake pressure) thus ensuring greater efficiency.‎
The Flash injection technology then injects two-phase refrigerant (gas and liquid) at medium pressure inside the compressor spirals so as to obtain two compression stages with better efficiency and high performance at low temperature.‎
The brazed plate exchanger inside the outdoor unit used for undercooling increases the exchange efficiency by 30% compared to the classic Shell&Tube models and by 50% compared to the double tube models.‎
Each DVM S outdoor unit has 1-2 Samsung Inverter compressors, all equipped with Flash injection technology.‎
The DVM system allows a quick and simple installation, as the connection between the indoor units and the outdoor units is made through the use of two copper pipes, in which the refrigerant fluid R410A circulates.‎
The operating limits are very high: 48°C in cooling and -25°C in heating, to ensure a high level of comfort and efficiency throughout the year.‎
The DVM S HR allows connected indoor units to operate in heating or cooling mode simultaneously (thanks to the heat recovery that ensures a high energy saving) to satisfy the various installation requirements or the different exposures to irradiation.‎
The correct flow of refrigerant inside the evaporator is regulated by an electronic expansion valve (EEV) to 2000 step which is able to vary instantly, thanks to the continuous dialogue between the internal and external PCB, the passage of the refrigerant.‎

Dimensiones
AM017FNLDEH/EU :700 x 199 x 600 mm
AM022FNLDEH/EU: 700 x 199 x 600 mm
AM028FNLDEH/EU: 700 x 199 x 600 mm
AM036FNLDEH/EU: 700 x 199 x 600 mm
AM045FNLDEH/EU: 900 x 199 x 600 mm
AM056FNLDEH/EU: 900 x 199 x 600 mm
AM071FNLDEH/EU: 1100 x 199 x 600 mm
Bim y Cad
AutoCAD
Revit

Colección DVM S por Samsung
También te recomendamos...
Productos vistos recientemente
Download BIM/CAD
AutoCAD
4
DVM S - Slim AM 022 028 036 FNLDEH
DVM S - Slim AM 017 FNLDEH
DVM S - Slim AM 071 FNLDEH
DVM S - Slim AM 045 056 FNLDEH
Download BIM/CAD
Revit
3
SAMSUNG_DVM S SLIM 45-56 / MSP 22-28
SAMSUNG_DVM S SLIM 17-22-28-36
SAMSUNG_DVM S SLIM 71

Guardar en:

Conferma la tua posizione

per scoprire le offerte valide nella tua zona

CAP
OK
Usa la mia posizione
Síguenos en
Guardar en: