Samsung Climate Solutions
DVM Chiller - CASSETTA 360

Equipo de aire acondicionado mono-split de techo comercial

Download BIM/CAD
AutoCAD
2
Revit
2
Solicitar un archivo BIM / CAD

Product
Samsung Climate Solutions / DVM Chiller - CASSETTA 360 / Equipo de aire acondicionado mono-split de techo comercial

AÑADIR A TU LISTA DE DESEOS O PROYECTO
Resumen

DVM Chiller - CASSETTA 360 By Samsung Climate Solutions

Colección
Tipo

Equipo de aire acondicionado mono-split de techo comercial

• air discharge at 360° without distributor fins ("coanda" effect)
• Fan with inverter motor; outdoor air inlet predisposition
• Built-in condensate drain pump (750 mmh2o); antibacterial filter included
• Communication with "Nasa" protocol
• SPI Air purifier device (optional)
• Circular or square box panel, black or white
• Power supply: single-phase 220 V - 50 Hz

Product codes:
AG060MN4PKH/EU
AG072MN4PKH/EU
AG090MN4PKH/EU
AG105MN4PKH/EU

The Samsung DVM chiller allows, thanks to the exclusive use of the dual inverter compressor (produced by Samsung), a high efficiency at partial loads and a fast start-up in heating/cooling, while Flash injection technology ensures high performance especially at low temperatures.‎
The variable flow of refrigerant technology optimizes the consumption of electricity as it is able to vary the power supplied according to the thermal demand in the rooms to be air conditioned.‎
The cycle efficiency with Inverter scroll compressor and Flash injection technology is superior to that of a traditional compressor, as the additional capacity resulting from undercooling is obtained with less power absorbed: the steam, produced in the undercooling process, is compressed only from an intermediate pressure (higher than the intake pressure) thus ensuring greater efficiency.‎
The Flash injection technology then injects two-phase refrigerant (gas and liquid) at medium pressure inside the compressor spirals so as to obtain two compression stages with better efficiency and high performance at low temperature.‎
The brazed plate exchanger inside the outdoor unit used for undercooling increases the exchange efficiency by 30% compared to the classic Shell&Tube models and by 50% compared to the double tube models.‎
Each outdoor DVM chiller unit is equipped with 2 Samsung Inverter compressors, all equipped with Flash injection technology.‎
The sizes available are from 15-20-25HP (without integrated pump) and it is possible to combine up to 16 modules to reach the power of 1040 kW.‎
The operating limits are very high: 48°C in cooling and -25°C in heating and max water delivery temperature 55°C .‎
A major advantage is the ability to connect the same standard DVM external control systems;through a dedicated card in fact it is possible to interface the water coil with local wired controls and with the centralized systems of the products to direct expansion.‎

Dimensiones
AG060MN4PKH/EU: 947 x 281 x 947 mm
AG072MN4PKH/EU: 947 x 365 x 947 mm
AG090MN4PKH/EU: 947 x 365 x 947 mm
AG105MN4PKH/EU: 947 x 365 x 947 mm
Bim y Cad
AutoCAD
Revit

Colección DVM Chiller por Samsung Climate Solutions
También te recomendamos...
Productos vistos recientemente
Download BIM/CAD
AutoCAD
2
DVM Chiller - Cassette 360 - squared panel
DVM Chiller - Cassette 360 - round panel
Download BIM/CAD
Revit
2
SAMSUNG_DVM Chiller - CASSETTE 360° - 60
SAMSUNG_DVM Chiller - CASSETTE 360° - 72-90-105

Guardar en:

Conferma la tua posizione

per scoprire le offerte valide nella tua zona

CAP
OK
Usa la mia posizione
Guardar en: